How to Repair a Leaking Pressure-Assisted Toilet
A pressure-assisted toilet that continues to run after the flush often does so for the same reason that a standard gravity toilet does. When you have a leak between the tank and the bowl of a toilet, it is because of problems either with the bolts holding the tank to the bowl or with the gasket that fits between the tank and the bowl.
Since the parts are different, repairing this problem in a pressure-assisted toilet is just a little different than for a gravity toilet. Even though the tank interior of a pressure-assisted toilet looks completely different, don’t let that discourage you from making repairs. The toilet shown here is a Flushmate-style (power flush) toilet, which requires a special gasket.
What You'll Need
Equipment / Tools
- Tongue-and-groove pliers
- Socket wrench or adjustable wrench
- Mini hacksaw (as needed)
Materials
- Tank bolts and washers
- Pressure tank gasket (optional)
Instructions
-
Empty the Tank
Shut off the water by closing the shutoff valve on the water supply line under the toilet. Empty the toilet tank by flushing. This will remove the pressure from the pressure tank inside the toilet tank.
Disconnect the water line that extends into the pressure tank from the water inlet valve. Flush a couple more times to help drain the pressure tank of any residual water.
From outside the toilet tank, disconnect the water supply tube that is attached to the tailpiece of the water inlet valve, located usually on the bottom left side of the toilet tank. You may need channel-type pliers to loosen the fitting on the supply tube.
-
Remove the Tank Bolts
Find the toilet bolts that secure the toilet tank to the bowl, located below the tank and behind the bowl. You may be able to get at them from outside the tank with a socket wrench and a deep socket or with an adjustable wrench.
If the bolts will not come off easily, you may have to cut them. With a skinny hacksaw blade or other thin cutting tool, cut the bolts off in the narrow space between the toilet tank and the toilet bowl. Since you will be installing new toilet bolts, it's okay if you ruin the old bolts.
There may be another set of nuts and washers holding the bolts onto the tank. Either unscrew the nuts and remove the bolts or cut away the rusted nuts to remove them. Once again, a skinny blade can be wedged between the tank and the nut to cut it out.
Lift off the toilet tank and set it down. Take the bolts out, and clean the area between the tank and the bowl in preparation for installing the new bolts.
-
Install the New Tank Bolts
You may need to remove the pressure tank from the inside of the toilet tank in order to put in the new tank bolts. To do this, unscrew the large plastic mounting nut from the tailpiece of the pressure tank where it extends through the bottom of the toilet tank. The pressure tank unit should easily pull out of the toilet tank.
Put a rubber washer on each of the new tank bolts, then slide the bolts through the mounting holes from inside the tank.
On the bottom of the tank exterior, install another rubber washer onto each bolt, then thread nuts onto them. Tighten up the nuts, a little bit at a time, so they are snug, and slightly squeeze the rubber washers. Do not overtighten; it is possible to crack the porcelain of the tank.
-
Replace the Gasket (Optional)
If your toilet seems to be leaking at the tank-to-bowl joint, replace the gasket on the tailpiece of the pressure tank. Remove the old gasket by just pulling it off. Push the new gasket into position around the tailpiece. It should fit completely around the plastic mounting nut.
-
Reinstall the Tank
Reset the tank onto the toilet bowl, inserting the tank bolts down through the holes in the rear platform on the toilet bowl. Thread the washers and nuts onto the tank bolts, and tighten them down evenly until the tank is secure and does not wobble. The pressure tank gasket should slightly compress as you tighten.
-
Check for Leaks
Reattach the water supply tube to the tailpiece of the water inlet valve extending out the bottom of the toilet tank, and tighten it gently with pliers. Turn on the water shutoff valve and inspect for leaks at the connection.
Fill the tank back up and flush it a number of times to make sure there are no more leaks. If your tank is still a little loose, the extra weight from the water in the tank will help you tighten the tank a bit more.