How to Replace a Lawn Irrigation Sprinkler Valve

Lawn irrigation valve box exposed showing pipe and valve with wires

The Spruce / Kevin Norris

Project Overview
  • Working Time: 30 mins
  • Total Time: 2 hrs, 30 mins
  • Skill Level: Intermediate
  • Estimated Cost: $15 to $40

The valves that are included in a lawn and garden irrigation system control water flow to specific zones within the system. These control valves are typically located inside a valve box, which may contain four or more valves, depending on the system layout. Common symptoms of a faulty valve include:

  • Leaks around the valve or at the sprinkler head farthest from the valve (indicating the water doesn't completely shut off)
  • Inadequate water delivered to the sprinkler heads
  • Sprinkler heads that simply don't come on

Replacing a valve is a fairly easy job that requires basic plumbing supplies, though it does require some experience with joining PVC pipe with solvent cement. The most important part of this project is getting an exact replacement part for the sprinkler valve. Determine the type and size of the valve, or remove it and bring it to the store with you. When selecting the new valve, make sure the PVC adapters fit the valve sockets before leaving the store. These adapters have a male threaded end to attach to the valve and a female slip-fit end designed to be solvent-glued to the PVC irrigation pipe.

Before You Begin

Shut off the water to the irrigation system by rotating the valve handle on the main supply pipe of the system. The valve is closed when the handle is perpendicular to the pipe. If there is no shutoff valve for the irrigation system, you may have to shut off the water at the home's main shutoff or the water meter.

What You'll Need

Equipment / Tools

  • Smartphone or camera (optional)
  • Reciprocating saw, PVC pipe cutter, or hacksaw
  • Utility knife or sandpaper
  • Tongue-and-groove pliers

Materials

  • New sprinkler valve
  • PVC MIP adapters (2 or more, as needed
  • Plumber's tape (thread-seal tape)
  • PVC primer and solvent glue

Instructions

Materials and tools to replace a lawn irrigation sprinkler valve

The Spruce / Kevin Norris

  1. Disconnect the Wiring

    Note where the low-voltage wires are attached to the old sprinkler valve. This is important because you must connect the wires to the new valve in the same way. It's a good idea to arrange the wires so that each can be seen clearly, then take a photo of the wiring with a smartphone or digital camera.

    When you're ready, disconnect the wires from the sprinkler valve.

    Low-voltage wires disconnected from sprinkler valve in exposed valve box

    The Spruce / Kevin Norris

  2. Remove the Old Valve

    Cut through the PVC irrigation pipes just below the old PVC adapters, using a reciprocating saw, hacksaw, or PVC pipe cutter. Cut as close as possible to the old fittings to conserve the maximum amount of pipe length. The new sprinkler valve will be only slightly lower than the old one.

    Remove all plastic burrs around the cut edges with a utility knife or sandpaper, being careful not to let the debris drop into the pipes.

    Tip

    With the system shown here, the local code requires that the anti-siphon sprinkler valve must be at least 6 inches above the highest sprinkler head in the same zone when the head is in the popped-up position. Check with your local building department for specific height requirements that apply to your project. If your valve will not be high enough to meet the code requirement, you may need to use couplings and some additional pipe to raise the sprinkler valve to a higher position.

    PVC irrigation pipes cut through with yellow pipe cutter to remove old valve

    The Spruce / Kevin Norris

  3. Prepare the New Valve

    Install the new PVC male (MIP) adapters into the new sprinkler valve by wrapping plumber's tape around the threaded end of each adapter and threading it onto the valve socket. Tighten the adapters with tongue-and-groove pliers, being careful not to over-tighten them, which can crack the plastic parts.

    New PVC male adapters inserted into sprinkler valve

    The Spruce / Kevin Norris

  4. Install the New Valve

    Apply PVC primer and solvent glue to the insides of the female adapter sockets and the outsides of the pipe ends, following the manufacturer's instructions.

    Fit the new valve onto the pipes, pushing down until the pipes are seated fully into the adapter sockets. Let the PVC solvent glue dry as directed by the manufacturer (usually two hours before testing).

    PVC primer and solvent glue added to outside of pipe ends to install new valve

    The Spruce / Kevin Norris

  5. Connect the Wiring and Test

    Connect the wires to the new valve in the same configuration that was used with the old valve. Turn the water back on by slowly rotating the shutoff valve's handle so it is parallel to the supply pipe. Check the valve and all connections for leaks.

    Verify that you installed the wires correctly by making sure the timer works with the new valve.

    Wires connected within new valve for testing

    The Spruce / Kevin Norris